# Example 9.34: Bland-Altman type plot

[This article was first published on

Want to share your content on R-bloggers? click here if you have a blog, or here if you don't.

**SAS and R**, and kindly contributed to R-bloggers]. (You can report issue about the content on this page here)Want to share your content on R-bloggers? click here if you have a blog, or here if you don't.

The Bland-Altman plot is a visual aid for assessing differences between two ways of measuring something. For example, one might compare two scales this way, or two devices for measuring particulate matter.

The plot simply displays the difference between the measures against their average. Rather than a statistical test, it is intended to demonstrate both typical differences between the measures and any patterns such differences may take. The utility of the plot, as compared with linear regression or sample correlation is that the plot is not affected by the range, while the sample correlation will typically increase with the range. In contrast, linear regression shows the strength of the linear association but not how closely the two measures agree. The Bland-Altman plot allows the user to focus on differences between the measures, perhaps focusing on the clinical relevance of these differences.

A peer reviewer recently asked a colleague to consider a Bland-Altman plot for two methods of assessing fatness: the familiar BMI (kg/m^2) and the actual fat mass measured by a sophisticated DXA machine. These are obviously not measures of the same thing, so a Bland-Altman plot is not exactly appropriate. But since the BMI is so simple to calculate and the DXA machine is so expensive, it would be nice if the BMI could be substituted for DXA fat mass.

For this purpose, we’ll generate a modified Bland-Altman plot in which each measure is first standardized to have mean 0 and standard deviation 1. The resulting plot should be assessed for pattern as usual, but typical differences must be considered on the standardized scale– that is, differences of a unit should be considered large, and good agreement might require typical differences of 0.2 or less.

**SAS**

Since this is a job we might want to repeat, we’ll build a SAS macro to do it. This will also demonstrate some useful features. The macro accepts a data set name and the names of two variables as input. We’ll comment on interesting features in code comments. If you’re an R coder, note that SAS macro variables are merely text, not objects. We have to manually assign “values” (i.e., numbers represented as text strings) to newly created macro variables.

%macro baplot(datain=,x=x,y=y); /* proc standard standardizes the variables and saves the results in the same variable names in the output data set. This means we can continue using the input variable names throughout. */ proc standard data = &datain out=ba_std mean=0 std=1; var &x &y; run; /* calculate differences and averages */ data ba; set ba_std; bamean = (&x + &y)/2;; badiff = &y-&x; run; ods output summary=basumm; ods select none; proc means data = ba mean std; var badiff; run; ods select all; /* In the following, we take values calculated from a data set for the confidence limits and store them in macro variables. That's the only way to use them later in code. The syntax is: call symput('varname', value); Note that 'bias' is purely nominal, as the standardization means that the mean difference is 0. */ data lines; set basumm; call symput('bias',badiff_mean); call symput('hici',badiff_mean+(1.96 * badiff_stddev)); call symput('loci',badiff_mean-(1.96 * badiff_stddev)); run; /* We use the macro variables just created in the vref= option below; vref draws reference line(s) on the vertical axis. lvref specifies a line type. */ symbol1 i = none v = dot h = .5; title "Bland-Altman type plot of &x and &y"; title2 "&x and &y standardized"; proc gplot data=ba; plot badiff * bamean / vref = &bias &hici &loci lvref=3; label badiff = "difference" bamean="mean"; run; %mend baplot;

Here is a fake sample data set, with the plot resulting from the macro shown above. An analysis would suggest that despite the correlation of 0.59 and p-value for the linear association < .0001, that these two measures don't agree too well.

data fake; do i = 1 to 50; /* the "42" in the code below sets the seed for the pseudo-RNG for this and later calls. See section 1.10.9. */ x = normal(42); y = x + normal(0); output; end; run; %baplot(datain=fake, x=x, y=y);

**R**

Paralleling SAS, we’ll write a small function to draw the plot, annotating within to highlight some details. If you’re primarily a SAS coder, note the syntax needed to find the name of an object submitted to a function. In contrast, assigning values to new objects created with the function is entirely natural. The resulting plot is shown below.

# set seed, for replicability set.seed(42) x = rnorm(50) y = x + rnorm(50) baplot = function(x,y){ xstd = (x - mean(x))/sd(x) ystd = (y - mean(y))/sd(y) bamean = (xstd+ystd)/2 badiff = (ystd-xstd) plot(badiff~bamean, pch=20, xlab="mean", ylab="difference") # in the following, the deparse(substitute(varname)) is what retrieves the # name of the argument as data title(main=paste("Bland-Altman plot of x and y\n", deparse(substitute(x)), "and", deparse(substitute(y)), "standardized"), adj=".5") #construct the reference lines on the fly: no need to save the values in new # variable names abline(h = c(mean(badiff), mean(badiff)+1.96 * sd(badiff), mean(badiff)-1.96 * sd(badiff)), lty=2) } baplot(x,y)

**An unrelated note about aggregators:**We love aggregators! Aggregators collect blogs that have similar coverage for the convenience of readers, and for blog authors they offer a way to reach new audiences. SAS and R is aggregated by R-bloggers, PROC-X, and statsblogs with our permission, and by at least 2 other aggregating services which have never contacted us. If you read this on an aggregator that does not credit the blogs it incorporates, please come visit us at SAS and R. We answer comments there and offer direct subscriptions if you like our content. In addition, no one is allowed to profit by this work under our license; if you see advertisements on this page, the aggregator is violating the terms by which we publish our work.

To

**leave a comment**for the author, please follow the link and comment on their blog:**SAS and R**.R-bloggers.com offers

**daily e-mail updates**about R news and tutorials about learning R and many other topics. Click here if you're looking to post or find an R/data-science job.

Want to share your content on R-bloggers? click here if you have a blog, or here if you don't.